Measure build-up of hydrocarbons on water.
ID-225 Oil thickness sensor
mitigate risk of water pollution
minimal maintenance
early detection
The LEAKWISE ID-225 Oil Thickness Sensor measures the thickness and monitors the buildup of hydrocarbons and other organic solvents on water.
There are two sub-models ID-225/100 & ID-225/200 for different maximum measured oil layer thicknesses: the ID-225 detects sheens as low as 1.0 mm and measures hydrocarbon thickness from 1-200 mm.
Many petroleum and power companies use the ID-225 for early detection, warning, and control of oil leaks and spills in the following applications:
- Remediation control
- Monitoring oil thickness changes over time in groundwater wells to enable effective oil removal methods
- Monitoring effectiveness of remediation techniques
- Implementing automatic on/off control
- Skim tanks — The ID-225 is inserted into a tank through an inspection hatch, enabling automatic starting and stopping of skimming operation with pre-set thickness parameters.
- Monitoring oil/water separators — An ID-225 can monitor oil layer thickness build up in the separator without human intervention.
- Wastewater sewer monitoring — Installing an ID-225 in the sewer near the process area will detect and control hydrocarbon leaks at the source, reducing the load from the treatment plant and preventing spills.
The ID-225 Oil Thickness Sensor is used in conjunction with one of three controllers, depending on the application.
- The PS-220 Controller is an analog signal processor and power supply in a NEMA 4 enclosure, and supports a single ID-220 Leakwise sensor.
- The SLC-220 Digital Signal Processor for Multiple (2 / 4 standard, more in a network) ID-220 Series sensor support, with various output options, including relay, lights, 4-20 mA, LCD, Modbus in RS-232 and RS-485 communication, and cellular remote connectivity.
- The WSP-220 Wireless communication – Point-to-Point data radio.
SPECIFICATIONS |
||
|
Resolution |
1 mm (0.04 in) |
|
|
Water level variation |
Minimum: 30 cm (~12 in) (33 cm for ID-225/200) above well/tank/sump bottom Maximum: 45 m (~150 ft) |
|
|
Water lateral velocity |
~20 cm/sec (~8 in/sec) when installed in a stilling well |
|
|
Water temperature |
0 to 70 °C (32 to 158° F); no freezing |
|
|
Air temperature |
-10 to 80° C (14 to 176° F) |
|
|
Materials |
Hydrocarbon resistant polymers, 316 stainless steel; |
|
|
Integral cable |
10 m (~33 ft.) supplied with sensor, additional length to order up to 50 m (164 ft) total |
|
|
ID-225/100 |
ID-225/200 |
|
|
Oil monitoring range |
1 to 100 mm (0.4 to 4.0 in) |
1 to 200 mm (0.4 to 8.0 in) |
|
Dimensions |
Ø 87 mm (3.43 in), height 150 mm (5.9 inch) |
Ø 87 mm (3.43 in), height 300 mm (11.8 in) |
CERTIFICATION |
||
|
ATEX Intrinsically Safe: II1G Ex ia IIC T4 Ga -40 °C to +70 °C. Also: IECEx and CETLUS |
||
|
Combined with PS220/N4, approved for operation in hazardous location. |
||
|
Performance |
EPA - Conforms to Spill Prevention, Control and Countermeasure (SPCC) - Oil Pollution |
|
|
Manufacture |
ISO 9001:2015 Certified |
|
ACCESSORIES |
||
|
Stilling well in 1 m & 2 m long sections, which can be assembled to any length |
||
|
Specifications vary for other sub-models - please enquire |
||
